Drag Racing Specialties

Innovators not Imitators

Plano, Texas                                                    Madison, Mississippi

bherrick@slotcar.com

DRS-101 Glueboard “With Handle & Non Skid Feet"

Glueboards are used to apply glue (traction compound) to your tires. Our method of doing this consists of applying two large dots of glue on your board and taking your index finger and smearing it around until it is smooth, and evenly applied on one end of the board.

Then you hold the front of your car with one hand and the rear of the car with your fingers up under the rear of the car. Then you roll the cars rear tires through the glue a few times and then turn the car upside down to make sure the glue is evenly applied around the tires.

Then take the car to the track and set the car down on the track perfectly straight about one inch behind the starting line. Then pick up your controller and drive the car down the track about ten feet as slow as possible to apply the glue evenly to the track.

How many times you do this depends on the type of car you race. When you feel you have enough glue applied glue your tires one final time and then set the front of the car down in the slot keeping the rear tires from touching the track.

Then move the car forward until the car is staged, and then set the rear of the car down perfectly straight and race from that position.

You will have to adjust how much glue you apply to both the glueboard and the track, but this is the method that works!

DRS-111 Screw In Motor Tab

Our Screw In Motor Tab "Fits All Sidewinder C-Can Chassis Except DRS-19, 20". It is used to make a car with a screw mounted motor. Unlike a stamped chassis this makes a very rigid mount that will keep your gear mesh where you set it. Good for the beginning racer and is not a permanent modification so when your soldering skills improve you can remove it

DRS-115 Replacement Rear Wheel Assembly For DRS-25, 26 Dragbike

These are complete with hub, tire, pulley, and set screw.

DRS-116 Replacement Drive Belt For DRS-25, 26 Dragbike

This is for motor pulley to rear wheel pulley.

DRS-117 Replacement Press On Motor Pulley For DRS-25, 26 Dragbike

DRS-118 Replacement Front Wheel Assembly For DRS-25, 26 Dragbike

DRS-124 .820 Diameter Solid Front Wheels 1/16” Axle Great For “Doorslammer” Type Cars

DRS-125 .500 Diameter Solid Front Wheels 1/16” Axle Great For “Funny Cars” Or “Dragsters”

These are the best value on the market. Heck you can buy two pairs of ours compared to some of the other vendors. Also these have a .050 axle hole so the wheels fit snug when you use the front axle for the front body mount (highly recommended) using stainless pin tubing.

DRS-135 Wheelie Bar For Stamped Steel Chassis

Put spring steel wheelie bars on your stamped steel chassis and end your problems with the ones made from wire.

DRS-138 Wheelie Bar Axle w/Wheels Fits All drag cars

Why take the time to build your own when you too can have the same wheelie bar axle set-up that we use.

DRS-144 Precision .047 Axle Wheelie Wheels

The best there is. Same as used in the DRS-138 wheelie bar axle.

DRS-145 Retrofit Pillowblocks

from DRS-49 Chassis .025” thick

DRS-146 Stainless Steel .050 Pintubing for Body Mounts

Used to mount bodies on all slot cars. You absolutely must use stainless pin tubing when you use the front axle for the front body mount (highly recommended).

DRS-148 Drilled.820 Front Wheels .050 Axle Great For “Doorslammer” Type Cars

DRS-149 Drilled.500 Front Wheels .050 Axle Great For “Funny Cars” Or “Dragsters”

These are the best value on the market. Heck you can buy two pairs of ours compared to some of the other vendors. Also these have a .050 axle hole so the wheels fit snug when you use the front axle for the front body mount (highly recommended) using stainless pin tubing.

DRS-156 Pillowblocks W/ Wheelie Bar Brace

Fits most of the drag chassis on the market. Works well with the new high downforce bodies like the DRS-506, 515, 516.

DRS-157 Inline Motor Tab

Fits DRS-43, 44, 45, 46, 67, 68, 71, 72. Allows the use of a screw in motor!

DRS-158 Body Pins

These have a larger shaft size for a great fit in .050 pin tubing.

DRS-161 Genuine DRS Stainless Steel Chassis Tubing

This tubing is the real deal. Bob found this tubing in 1986 and has used it ever since. As used in the “Gunslinger” Tube Chassis!

DRS-189 .050” Stainless Steel Pintubing 12” length

DRS-195 Spoked .820 Front Wheels .050 Axle